View AD5551BRZ_7492215.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

2.7 v to 5.5 v, serial-input, voltage-output, 14-bit dacs ad5551/ad5552 rev. a information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2000C2010 analog devices, inc. all rights reserved. features full 14-bit performance 3 v and 5 v single supply operation low 0.625 mw power dissipation 1 s settling time unbuffered voltage output capable of driving 60 k loads directly spi/qspi/microwire-compatible interface standards power-on reset clears dac output to 0 v (unipolar mode) 5 kv hbm esd classification applications digital gain and offset adjustment automatic test equipment data acquisition systems industrial process control general description the ad5551/ad5552 are single, 14-bit, serial-input, voltage- output dacs that operate from a single 2.7 v to 5.5 v supply. the dac output range extends from 0 v to v ref . these dacs provide 14-bit performance without any adjust- ments. the dac output is unbuffered, which reduces power consumption and offset errors contributed by an output buffer. with an external op amp, the ad5552 can be operated in bipolar mode generating a v ref output swing. the ad5552 also includes kelvin sense connections for the reference and analog ground pins to reduce layout sensitivity. for higher precision applications, refer to 16-bit dacs ad5541, ad5542, and ad5544. the ad5551/ad5552 utilize a versatile 3-wire interface that is compatible with spi, qspi?, microwire?, and dsp interface standards. the ad5551 and ad5552 are available in 8-lead and 14-lead soic packages. functional block diagrams 6 1 2 8 7 14-bit dac 14-bit data latch serial input regisiter v dd dgnd din v ref cs s clk 3 4 5 v out agnd ad5551 control logic 01943-001 figure 1. 14 12 14-bit data latch serial input regisiter v dd dgnd 11 ldac 8 sclk cs 7 din 10 2 v refs 5 v reff 6 v out 1 rfb 13 inv ad5552 3 agndf 4 agnds 14-bit dac r fb r inv control logic 01943-002 figure 2. product highlights 1. single supply operation. the ad5551 and ad5552 are fully specified and guaranteed for a single 2.7 v to 5.5 v supply. 2. low power consumption. typically 0.625 mw with a 5 v supply. 3. 3-wire serial interface. 4. unbuffered output capable of driving 60 k loads, which reduces power consumption as there is no internal buffer to drive. 5. power-on reset circuitry.
ad5551/ad5552 rev. a | page 2 of 16 table of contents features .............................................................................................. 1 applications ....................................................................................... 1 general description ......................................................................... 1 functional block diagrams ............................................................. 1 product highlights ........................................................................... 1 revision history ............................................................................... 2 specifications ..................................................................................... 3 timing characteristics ................................................................ 4 absolute maximum ratings ............................................................ 5 esd caution .................................................................................. 5 pin configurations and function descriptions ........................... 6 typical performance characteristics ............................................. 7 terminology .................................................................................... 10 theory of operation ...................................................................... 11 digital-to-analog section ......................................................... 11 serial interface ............................................................................ 11 unipolar output operation ...................................................... 11 bipolar output operation ......................................................... 12 output amplifier selection ....................................................... 12 force sense buffer amplifier selection ................................... 12 reference and ground ............................................................... 13 power-on reset .......................................................................... 13 power supply and reference bypassing .................................. 13 microprocessor interfacing ........................................................... 14 adsp-21xx to ad5551/ad5552 interface ............................. 14 68hc11 to ad5551/ad5552 interface ................................... 14 microwire to ad5551/ad5552 interface ........................ 14 80c51/80l51 to ad5551/ad5552 interface .......................... 14 applications information .............................................................. 15 optocoupler interface ................................................................ 15 decoding multiple ad5551/ad5552s .................................... 15 outline dimensions ....................................................................... 16 ordering guide .......................................................................... 16 revision history 5/10rev. 0 to rev. a updated format .................................................................. universal changes to data sheet title, features section, general description section, and product highlights section ................. 1 changes to specifications section .................................................. 3 changes to table 3 ............................................................................ 5 changes to pin v dd description in table 4 and table 5 ............. 6 changes to typical performance characteristics section ........... 7 changes to first paragraph in theory of operation section ... 11 updated outline dimensions ....................................................... 16 changes to ordering guide .......................................................... 16 7/00revision 0: initial version
ad5551/ad5552 rev. a | page 3 of 16 specifications v dd = 2.7 v to 5.5 v, 2.5 v v ref v dd , agnd = dgnd = 0 v. all specifications t a = t min to t max , unless otherwise noted. table 1. parameter 1 min typ max unit test condition static performance resolution 14 bits relative accuracy, inl 0.15 1.0 lsb b grade differential nonlinearity 0.15 0.8 lsb guaranteed monotonic gain error ?1.5 ?0.3 +0.5 lsb gain error temperature coefficient 0.1 ppm/c zero-code error 0.1 1 lsb zero-code temperature coefficient 0.05 ppm/c ad5552 bipolar resistor matching 1.000 / rfb/rinv, typically rfb = rinv = 28 k 0.0015 0.0152 % ratio error bipolar zero offset error 0.25 1 lsb bipolar zero temperature coefficient 0.2 ppm/c bipolar zero-code error ?0.3 1.2 lsb bipolar gain error ?0.3 1.2 lsb output characteristics 2 output voltage range 0 v ref ? 1 lsb v unipolar operation ?v ref v ref ? 1 lsb v ad5552 bipolar operation output voltage settling time 1 s to ? lsb of fs, c l = 10 pf slew rate 17 v/s c l = 10 pf, measured from 0% to 63% digital-to-analog glitch impulse 1.1 nv-sec 1 lsb change around the major carry digital feedthrough 0.2 nv-sec all 1s loaded to dac, v ref = 2.5 v dac output impedance 6.25 k tolerance typically 20% power supply rejection ratio 1.0 lsb v dd 10% dac reference input reference input range 2.0 v dd v reference input resistance 3 9 k unipolar operation 7.5 k ad5552, bipolar operation logic inputs input current 1 a v inl , input low voltage 0.8 v v inh , input high voltage 2.4 v input capacitance 2 10 pf hysteresis voltage 2 0.15 v reference 2 reference ?3 db bandwidth 2.2 mhz all 1s loaded reference feedthrough 1 mv p-p all 0s loaded, v ref = 1 v p-p at 100 khz signal-to-noise ratio 92 db reference input capacitance 26 pf code 0000 h 26 pf code 3fff h power requirements digital inputs at rails v dd 2.7 5.5 v i dd 125 150 a power dissipation 0.625 0.825 mw 1 temperature range is as follows: b version: ?40c to +85c; 2 guaranteed by design, not subject to production test. 3 reference input resistance is code-dependent, minimum at 2555 h .
ad5551/ad5552 rev. a | page 4 of 16 timing characteristics v dd = 2.7 v to 5.5 v, 2.5 v v ref 5.5 v, agnd = dgnd = 0 v. all specifications ?40c t a +85c, unless otherwise noted. table 2. limit at t min , t max parameter 1 , 2 all versions unit description f sclk 25 mhz max sclk cycle frequency t 1 40 ns min sclk cycle time t 2 20 ns min sclk high time t 3 20 ns min sclk low time t 4 15 ns min cs low to sclk high setup t 5 15 ns min cs high to sclk high setup t 6 35 ns min sclk high to cs low hold time t 7 20 ns min sclk high to cs high hold time t 8 15 ns min data setup time t 9 0 ns min data hold time t 10 30 ns min ldac pulse width t 11 30 ns min cs high to ldac low setup t 12 30 ns min cs high time between active periods 1 guaranteed by design, not production tested. 2 sample tested during initial release and after any redesign or process change that may affect this parameter. all input signal s are measured with tr = tf = 5 ns (10% to 90% of +3 v and timed from a voltage level of +1.6 v). sclk cs din ldac* db13 db0 t 6 t 4 t 12 t 8 t 9 t 2 t 3 t 1 t 7 t 5 t 10 t 11 *ad5552 only. may be tied permanently low if required. 01943-003 figure 3. timing diagram
ad5551/ad5552 rev. a | page 5 of 16 absolute maximum ratings t a = 25c unless otherwise noted table 3. parameter rating v dd to agnd C0.3 v to +6 v digital input voltage to dgnd C0.3 v to v dd + 0.3 v v out to agnd C0.3 v to v dd + 0.3 v agnd, agndf, agnds to dgnd C0.3 v to +0.3 v input current to any pin except supplies 10 ma operating temperature range industrial (b version) ?40c to +85c storage temperature range ?65c to +150c maximum junction temperature, (t j max) 150c package power dissipation (t j max C t a )/ ja thermal impedance ja soic (r-8) 149.5c/w soic (r-14) 104.5c/w lead temperature, soldering peak temperature 1 260c esd 2 5 kv 1 as per jedec standard 20. 2 hbm classification. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. esd caution
ad5551/ad5552 rev. a | page 6 of 16 pin configurations and function descriptions v out 1 agnd 2 v ref 3 cs 4 v dd 8 dgnd 7 din 6 sclk 5 ad5551 top view (not to scale) 01943-004 figure 4. ad5551 pin configuration rfb 1 v out 2 agndf 3 a gnds 4 v dd 14 inv 13 dgnd 12 ldac 11 v refs 5 din 10 v reff 6 nc 9 cs 7 sclk 8 ad5552 top view (not to scale) nc = no connecnt 01943-005 figure 5. ad5552 pin configuration table 4. ad5551 pin function descriptions pin no. mnemonic description 1 v out analog output voltage from the dac. 2 agnd ground reference point for analog circuitry. 3 v ref this is the voltage reference input for the dac. connect to external reference ranges from 2 v to v dd . 4 cs this is an active low-logic input signal. the chip select signal is used to frame the serial data input. 5 sclk clock input. data is clocked into the input register on the rising edge of sclk. duty cycle must be between 40% and 60%. 6 din serial data input. this device accepts 14-bit words. data is clocked into the input regist er on the rising edge of sclk . 7 dgnd digital ground. ground reference for digital circuitry. 8 v dd analog supply voltage, 2.7 v to 5.5 v 10%. table 5. ad5552 pin function descriptions pin no. mnemonic description 1 rfb feedback resistor. in bipolar mode, connect this pin to external op amp output. 2 v out analog output voltage from the dac. 3 agndf ground reference point for analog circuitry (force). 4 agnds ground reference point for analog circuitry (sense). 5 v refs this is the voltage reference input (sense) for the dac. connect to external reference ranges from 2 v to v dd . 6 v reff this is the voltage reference input (force) for the dac. connect to external reference ranges from 2 v to v dd . 7 cs this is an active low-logic input signal. the chip select signal is used to frame the serial data input. 8 sclk clock input. data is clocked into the input register on the rising edge of sclk. duty cycle must be between 40% and 60%. 9 nc no connect. 10 din serial data input. this device accepts 14-bit words. data is clocked into the input register on the rising edge of scl k. 11 ldac ldac input. when this input is taken low, the dac register is simultaneously updated with the contents of the input register. 12 dgnd digital ground. ground reference for digital circuitry. 13 inv connected to the internal scaling resistors of the dac. connect the inv pin to external op amps inverting input in bipolar mode. 14 v dd analog supply voltage, 2.7 v to 5.5 v 10%.
ad5551/ad5552 rev. a | page 7 of 16 typical performance characteristics 0.125 0.062 0 ?0.062 ?0.125 ?0.187 0 8192 16,384 24,576 32,768 40,960 49,152 57,344 65,536 code integral nonlinearity (lsb) v dd = 5v v ref = 2.5v 01943-006 figure 6. integral nonlinearity vs. code 0.062 0 ?0.062 ?0.125 ?0.187 ?0.250 ?60 ?40 ?20 0 20 40 60 80 100 120 140 temperature (c) integral nonlinearity (lsb) v dd = 5v v ref = 2.5v 01943-007 figure 7. integral nonlinearity vs. temperature 234567 supply voltage (v) linearity error (lsb) v ref = 2.5v t a = 25c dnl inl 0.125 0.062 0 ?0.062 ?0.125 ?0.187 0 1943-008 figure 8. linearity error vs. supply voltage 0 8192 16,384 24,576 32,768 40,960 49,152 57,344 65,536 code differential nonlinearity (lsb) v dd = 5v v ref = 2.5v 0.125 0.062 0 ?0.062 ?0.125 01943-009 figure 9. differential nonlinearity vs. code 0.187 0.125 0.062 0 ?0.062 ?0.125 ?60 ?40 ?20 0 20 40 60 80 100 120 140 temperature (c) differential nonlinearity (lsb) v dd = 5v v ref = 2.5v 01943-010 figure 10. differential nonlinearity vs. temperature 0123456 reference voltage (v) linearity error (lsb) v dd = 5v t a = 25c dnl inl 0.187 0.125 0.062 0 ?0.062 ?0.125 0 1943-011 figure 11. linearity error vs. reference voltage
ad5551/ad5552 rev. a | page 8 of 16 0 ?0.025 ?0.050 ?0.075 ?0.100 ?0.125 ?0.150 ?0.175 ?0.200 ?0.225 ?40 25 85 temperature (c) gain error (lsb) v dd = 5v v ref = 2.5v t a = 25c 01943-012 figure 12. gain error vs. temperature 132 116 118 120 122 124 126 128 130 ?40 25 85 temperature (c) supply current (a) v dd = 5v v ref = 2.5v t a = 25c 01943-013 figure 13. supply current vs. temperature 200 0 20 40 60 80 100 120 140 160 180 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 digital input voltage (v) supply current (v) 01943-014 figure 14. supply current vs. digital input voltage 0.037 ?0.037 ?0.025 ?0.012 0 0.012 0.025 ?40 25 85 temperature (c) zero-code error (lsb) v dd = 5v v ref = 2.5v t a = 25c 01943-015 figure 15. zero-code offset error vs. temperature 0 0.5 1.0 1.5 2.0 0123456 supply current (a) voltage (v) reference voltage v dd = 5v supply voltage v ref = 2.5v t a = 25c 01943-016 figure 16. supply current vs. reference voltage or supply voltage 200 150 100 50 0 0 70,000 60,000 50,000 40,000 30,000 20,000 10,000 code (decimal) reference current (a) v dd = 5v v ref = 2.5v t a = 25c 01943-017 figure 17. reference current vs. code
ad5551/ad5552 rev. a | page 9 of 16 2s/div v ref = 2.5v v dd = 5v t a = 25c din (5v/div) v out (50mv/div) 01943-018 figure 18. digital feedthrough voltage (v) digital voltage (v) 1.236 1.234 1.232 1.230 1.228 1.226 1.224 ?0.5 0 0.5 1.0 1.5 2.0 5 0 ?5 ?10 ?15 ?20 ?25 ?30 time (ns) v out cs 01943-019 figure 19. digital-to-analog glitch impulse 2s/div v ref = 2.5v v dd = 5v t a = 25c 200pf 10pf 50pf 100pf cs (5v/div) v out (0.5v/div) 01943-020 figure 20. large signal settling time 0.5s/div v ref = 2.5v v dd = 5v t a = 25c v out (1v/div) v out (50mv/div) gain = ?216 01943-021 figure 21. small signal settling time
ad5551/ad5552 rev. a | page 10 of 16 terminology relative accuracy for the dac, relative accuracy or integral nonlinearity (inl) is a measure of the maximum deviation, in lsbs, from a straight line passing through the endpoints of the dac transfer function. a typical inl vs. code plot can be seen in figure 6 . differential nonlinearity differential nonlinearity is the difference between the measured change and the ideal 1 lsb change between any two adjacent codes. a specified differential nonlinearity of 1 lsb maximum ensures monotonicity. a typical dnl vs. code plot can be seen in figure 9 . gain error gain error is the difference between the actual and ideal analog output range, expressed as a percent of the full-scale range. it is the deviation in slope of the dac transfer characteristic from ideal. gain error temperature coefficient this is a measure of the change in gain error with changes in temperature. it is expressed in ppm/c. zero-code error zero code error is a measure of the output error when zero code is loaded to the dac register. zero-code temperature coefficient this is a measure of the change in zero code error with a change in temperature. it is expressed in mv/c. digital-to-analog glitch impulse digital-to-analog glitch impulse is the impulse injected into the analog output when the input code in the dac register changes state. it is normally specified as the area of the glitch in nv-sec and is measured when the digital input code is changed by 1 lsb at the major carry transition. a plot of the glitch impulse is shown in figure 19 . digital feedthrough digital feedthrough is a measure of the impulse injected into the analog output of the dac from the digital inputs of the dac, but is measured when the dac output is not updated. cs is held high, while the clk and din signals are toggled. it is specified in nv-sec and is measured with a full-scale code change on the data bus, that is, from all 0s to all 1s and vice versa. a typical plot of digital feedthrough is shown in . figure 18 power supply rejection ratio this specification indicates how the output of the dac is affected by changes in the power supply voltage. power-supply rejection ratio is quoted in terms of % change in output per % change in v dd for full-scale output of the dac. v dd is varied by 10%. reference feedthrough this is a measure of the feedthrough from the v ref input to the dac output when the dac is loaded with all 0s. a 100 khz, 1 v p-p is applied to v ref . reference feedthrough is expressed in mv p-p.
ad5551/ad5552 rev. a | page 11 of 16 theory of operation the ad5551/ad5552 are single, 14-bit, serial input, voltage output dacs. they operate from a single supply ranging from 2.7 v to 5.5 v and consume typically 125 a with a supply of 5 v. data is written to these devices in a 14-bit word format, via a 3-or 4-wire serial interface. to ensure a known power-up state, these parts were designed with a power-on reset function. in unipolar mode, the output is reset to 0 v, while in bipolar mode, the ad5552 output is set to ?v ref . kelvin sense connections for the reference and analog ground are included on the ad5552. digital-to-analog section the dac architecture consists of two matched dac sections. a simplified circuit diagram is shown in figure 22 . the dac architecture of the ad5551/ad5552 is segmented. the four msbs of the 14-bit data word are decoded to drive 15 switches, e1 to e15. each of these switches connects one of 15 matched resistors to either agnd or v ref . the remaining 10 bits of the data word drive switches s0 to s9 of a 10-bit voltage mode r-2r ladder network. 2r . . . . . s1 . . . . . 2r s9 2r e1 2r . . . . . e2 . . . . . 2r 2r s0 2r e15 r r v ref v out 10-bit r-2r ladder four msbs decoded into 15 equal segments 0 1943-022 figure 22. dac architecture with this type of dac configuration, the output impedance is independent of code, while the input impedance seen by the reference is heavily code dependent. the output voltage is dependent on the reference voltage as shown in the following equation: n ref out dv v 2 = where: d is the decimal data word loaded to the dac register. n is the resolution of the dac. for a reference of 2.5 v, the equation simplifies to the following, 384,16 5.2 d v out = this gives a v out of 1.25 v with midscale loaded, and a v out of 2.5 v with full-scale loaded to the dac. the lsb size is v ref /16,384. serial interface the ad5551/ad5552 are controlled by a versatile 3-wire serial interface, which operates at clock rates up to 25 mhz and is compatible with spi, qspi, microwire, and dsp interface standards. the timing diagram can be seen in figure 3 . input data is framed by the chip select input, cs . after a high-to-low transition on cs , data is shifted synchronously and latched into the input register on the rising edge of the serial clock, sclk. data is loaded msb first in 14-bit words. after 14 data bits have been loaded into the serial input register, a low-to-high transition on cs transfers the contents of the shift register to the dac. data can only be loaded to the part while cs is low. the ad5552 has an ldac function that allows the dac latch to be updated asynchronously by bringing ldac low after cs goes high. ldac should be maintained high while data is written to the shift register. alternatively, ldac may be tied permanently low to update the dac synchronously. with ldac tied permanently low, the rising edge of cs loads the data to the dac. unipolar output operation these dacs are capable of driving unbuffered loads of 60 k. unbuffered operation results in low-supply current, typically 300 a, and a low-offset error. the ad5551 provides a unipolar output swing ranging from 0 v to v ref . the ad5552 can be con- figured to output both unipolar and bipolar voltages. figure 23 shows a typical unipolar output voltage circuit. the code table for this mode of operation is shown in tabl e 6 . v out v reff * dgnd agnd v dd din sclk cs ad5551/ ad5552 ad820/ op196 v refs * + 0.1f 0.1f 10f unipolar output external op amp 2.5 v 5 v ldac* *ad5552 only. serial interface 01943-023 figure 23. unipolar output tale 6. unipolar code tale dac latch contents msb lsb analog output 11 1111 1111 1111 v ref (16,383/16,384) 10 0000 0000 0000 v ref (8192/16,384) = ? v ref 00 0000 0000 0001 v ref (1/16,384) 00 0000 0000 0000 0 v
ad5551/ad5552 rev. a | page 12 of 16 assuming a perfect reference, the worst-case output voltage may be calculated from the following equation: () inlvvv d v zse ge ref uniout +++= ? 14 2 where: v outCuni is the unipolar mode worst-case output. d is the decimal code loaded to the dac. v ref is the reference voltage applied to part. v ge is the gain error in volts. v zse is the zero-scale error in volts. inl is the integral nonlinearity in volts. bipolar output operation with the aid of an external op amp, the ad5552 may be confi- gured to provide a bipolar voltage output. a typical circuit of such operation is shown in figure 24 . the matched bipolar offset resistors r fb and r inv are connected to an external op amp to achieve this bipolar output swing where r fb = r inv = 28 k. table 7 shows the transfer function for this output operating mode. also provided on the ad5552 are a set of kelvin connections to the analog ground inputs. +5v ?5v v out inv rfb v reff agndf agnds v dd din sclk cs ad5552 v refs dgnd + 0.1f 0.1f 10f unipolar output external op amp 2.5 v 5 v ldac serial interface r inv r fb 01943-024 figure 24. bipolar output (ad5552 only) tale 7. bipolar code tale dac latch contents msb lsb analog output 11 1111 1111 1111 +v ref (8191/8192) 10 0000 0000 0000 +v ref (1/8192) 00 0000 0000 0001 0 v 00 0000 0000 0000 ?v ref (1/8192) 00 0000 0000 0000 ?v ref (8191/8192) = Cv ref assuming a perfect reference, the worst-case bipolar output voltage may be calculated from the following equation. ard rdvrdv v v ref os uniout bipout /)2(1 )1()2)( [( ++ + ?+ + = ? ? where: v os is the external op amp input offset voltage. rd is the r fb and r in resistor matching error, unitless. a is the op amp open-loop gain. output amplifier selection for bipolar mode, use a precision amplifier, supplied from a dual power supply. this provides the v ref output. in a single- supply application, selection of a suitable op amp may be more difficult as the output swing of the amplifier does not usually include the negative rail, in this case agnd. this can result in some degradation of the specified performance unless the application does not use codes near zero. the selected op amp needs to have a very low-offset voltage, (the dac lsb is 152 v with a 2.5 v reference), to eliminate the need for output offset trims. input bias current should also be very low as the bias current multiplied by the dac output impedance (approximately 6k) adds to the zero-code error. rail-to-rail input and output performance is required. for fast settling, the slew rate of the op amp should not impede the settling time of the dac. output impedance of the dac is constant and code-independent, but to minimize gain errors, the input impedance of the output amplifier should be as high as possible. the amplifier should also have a 3 db bandwidth of 1 mhz or greater. the amplifier adds another time constant to the system, therefore increasing the settling time of the output. a higher 3 db amplifier bandwidth results in a faster effective settling time of the combined dac and amplifier. force sense buffer amplifier selection these amplifiers can be single-supply or dual supplies, low noise amplifiers. a low-output impedance at high frequencies is preferred as they need to be able to handle dynamic currents of up to 20 ma.
ad5551/ad5552 rev. a | page 13 of 16 reference and ground as the input impedance is code-dependent, the reference pin should be driven from a low-impedance source. the ad5551/ ad5552 operate with a voltage reference ranging from 2 v to v dd . although dacs full-scale output voltage is determined by the reference, references below 2 v results in reduced accuracy. table 6 and table 7 outline the analog output voltage for particular digital codes. for optimum performance, kelvin sense connections are provided on the ad5552. if the application does not require separate force and sense lines, they should be tied together close to the package to minimize voltage drops between the package leads and the internal die. adr291 and adr293 are suitable references for this product. power-on reset these parts have a power-on reset function to ensure the output is at a known state upon power-up. after power-up, the dac register contains all zeros, until data is loaded from the serial register. however, the serial register is not cleared on power-up, so its contents are undefined. when loading data initially to the dac, 14 bits or more should be loaded to prevent erroneous data appearing on the output. if more than 14 bits are loaded, only the last 14 are kept, and if fewer than 14 are loaded, bits remain from the previous word. if the ad5551/ad5552 needs to be interfaced with data shorter than 14 bits, the data should be padded with zeros at the lsbs. power supply and reference bypassing for accurate high-resolution performance, it is recommended that the reference and supply pins be bypassed with a 10 f tantalum capacitor in parallel with a 0.1 f ceramic capacitor.
ad5551/ad5552 rev. a | page 14 of 16 microprocessor interfacing microprocessor interfacing to the ad5551/ad5552 is via a serial bus that uses standard protocol compatible with dsp processors and microcontrollers. the communications channel requires a 3-wire interface consisting of a clock signal, a data signal and a synchronization signal. the ad5551/ad5552 require a 14-bit data word with data valid on the rising edge of sclk. the dac update may be done automatically when all the data is clocked in or it may be done under control of ldac (ad5552 only). adsp-21xx to ad5551/ad5552 interface figure 25 shows a serial interface between the ad5551/ad5552 and the adsp-21xx. the adsp-21xx should be set to operate in the sport (serial port) transmit alternate framing mode. the adsp-21xx is programmed through the sport control register and should be configured as follows: internal clock operation, active low framing, 16-bit word length. the first 2 bits are dont care as ad5551/ad5552 keeps the last 14 bits. transmission is initiated by writing a word to the tx register after the sport has been enabled. because of the edges-triggered difference, an inverter is required at the sclks between the dsp and the dac. din sclk dt sclk ad5551/ ad5552 * adsp-21xx* *additional pins omitted for clarity. **ad5552 only. cs tfs ldac** fo 01943-025 figure 25. adsp-21xx to ad5551/ad5552 interface 68hc11 to ad5551/ad5552 interface figure 26 shows a serial interface between the ad5551/ad5552 and the 68hc11 microcontroller. sck of the 68hc11 drives the sclk of the dac, while the mosi output drives the serial data line din. cs signal is driven from one of the port lines. the 68hc11 is configured for master mode; mstr = 1, cpol = 0, and cpha = 0. data appearing on the mosi output is valid on the rising edge of sck. din sclk mosi sck ad5551/ ad5552 * 68hc11/ 68l11* *additional pins omitted for clarity. **ad5552 only. cs pc7 ldac** pc6 01943-026 figure 26. 68hc11/68l11 to ad5551/ad5552 interface microwire to ad5551/ad5552 interface figure 27 shows an interface between the ad5551/ad5552 and any microwire-compatible device. serial data is shifted out on the falling edge of the serial clock and into the ad5551/ ad5552 on the rising edge of the serial clock. no glue logic is required as the dac clocks data into the input shift register on the rising edge. din sclk so sclk ad5551/ ad5552* microwire* * additional pins omitted for clarity. cs cs 0 1943-027 figure 27. microwire to ad5551/ad5552 interface 80c51/80l51 to ad5551/ad5552 interface a serial interface between the ad5551/ad5552 and the 80c51/ 80l51 microcontroller is shown in figure 28 . txd of the micro- controller drives the sclk of the ad5551/ad5552, while rxd drives the serial data line of the dac. p3.3 is a bit programmable pin on the serial port which is used to drive cs . din sclk rxd txd ad5551/ ad5552* 80c51/ 80l51* *additional pins omitted for clarity. **ad5552 only. cs p3.3 ldac** p3.4 01943-028 figure 28. 80c51/80l51 to ad5551/ad5552 interface the 80c51/80l51 provides the lsb first, while the ad5551/ ad5552 expect the msb of the 14-bit word first. take care to ensure that the transmit routine takes this into account. usually it can be done through software by shifting out and accumu- lating the bits in the correct order before inputting to the dac. also, 80c51 outputs 2 byte words/16 bits data, thus the first two bits, after rearrangement, should be dont care as they are dropped from the 14-bit word of the dac. when data is to be transmitted to the dac, p3.3 is taken low. data on rxd is valid on the falling edge of txd, so the clock must be inverted as the dac clocks data into the input shift register on the rising edge of the serial clock. the 80c51/80l51 transmits its data in 8-bit bytes with only eight falling clock edges occur- ring in the transmit cycle. as the dac requires a 14-bit word, p3.3 (or any one of the other programmable bits) is the cs input signal to the dac, so p3.3 should be brought low at the beginning of the 16-bit write cycle 2 8 bit words and held low until the 16-bit 2 8 cycle is completed. after that, p3.3 is brought high again and the new data loads to the dac. again, the first two bits, after rearranging, should be dont care. ldac on the ad5552 may also be controlled by the 80c51/80l51 serial port output by using another bit programmable pin, p3.4.
ad5551/ad5552 rev. a | page 15 of 16 applications information optocoupler interface the digital inputs of the ad5551/ad5552 are schmitt- triggered, so they can accept slow transitions on the digital input lines. this makes these parts ideal for industrial applica- tions where it may be necessary that the dac is isolated from the controller via optocouplers. figure 29 illustrates such an interface. 10f 0.1f v out v dd power gnd 5v regulator ad5551/ ad5552 10k? v dd cs cs din 10k? v dd din 10k? v dd sclk sclk 01943-029 figure 29. ad5551/ad5552 in an optocoupler interface decoding multiple ad5551/ad5552s the cs pin of the ad5551/ad5552 can be used to select one of a number of dacs. all devices receive the same serial clock and serial data, but only one device receives the cs signal at any one time. the dac addressed is determined by the decoder. there is some digital feedthrough from the digital input lines. using a burst clock minimizes the effects of digital feedthrough on the analog signal channels. shows a typical circuit. figure 30 ad5551/ ad5552 cs din sclk v out ad5551/ ad5552 cs din sclk v out ad5551/ ad5552 cs din sclk v out ad5551/ ad5552 cs din sclk v out v dd dgnd en coded address sclk din enable decoder 01943-030 figure 30. addressing multiple ad5551/ad5552s
ad5551/ad5552 rev. a | page 16 of 16 outline dimensions controlling dimensions are in millimeters; inch dimensions (in parentheses) are rounded-off millimeter equivalents for reference only and are not appropriate for use in design. compliant to jedec standards ms-012-aa 012407-a 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) 0.50 (0.0196) 0.25 (0.0099) 45 8 0 1.75 (0.0688) 1.35 (0.0532) seating plane 0.25 (0.0098) 0.10 (0.0040) 4 1 85 5.00 (0.1968) 4.80 (0.1890) 4.00 (0.1574) 3.80 (0.1497) 1.27 (0.0500) bsc 6.20 (0.2441) 5.80 (0.2284) 0.51 (0.0201) 0.31 (0.0122) coplanarity 0.10 figure 31. 8-lead standard small outline package [soic_n] narrow body (r-8) dimensions shown in millimeters and (inches) controlling dimensions are in millimeters; inch dimensions (in parentheses) are rounded-off millimeter equivalents for reference only and are not appropriate for use in design. compliant to jedec standards ms-012-ab 060606-a 14 8 7 1 6.20 (0.2441) 5.80 (0.2283) 4.00 (0.1575) 3.80 (0.1496) 8.75 (0.3445) 8.55 (0.3366) 1.27 (0.0500) bsc seating plane 0.25 (0.0098) 0.10 (0.0039) 0.51 (0.0201) 0.31 (0.0122) 1.75 (0.0689) 1.35 (0.0531) 0.50 (0.0197) 0.25 (0.0098) 1.27 (0.0500) 0.40 (0.0157) 0.25 (0.0098) 0.17 (0.0067) coplanarity 0.10 8 0 45 figure 32. 14-lead standard small outline package [soic_n] narrow body (r-14) dimensions shown in millimeters and (inches) ordering guide model 1 inl dnl temperature range package description package option AD5551BRZ 1 lsb 0.8 lsb ?40c to +85c 8-lead soic_n r-8 AD5551BRZ-reel7 1 lsb 0.8 lsb ?40c to +85c 8-lead soic_n r-8 ad5551br 1 lsb 0.8 lsb ?40c to +85c 8-lead soic_n r-8 ad5551br-reel7 1 lsb 0.8 lsb ?40c to +85c 8-lead soic_n r-8 ad5552brz 1 lsb 0.8 lsb ?40c to +85c 14-lead soic_n r-14 1 z = rohs compliant part. ?2000C2010 analog devices, inc. all rights reserved. trademarks and registered trademarks are the prop erty of their respective owners. d01943-0-5/10(a)

▲Up To Search▲

Price & Availability of AD5551BRZ

	To Download AD5551BRZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .